This works well and prevents the existence of ground loops, a common source of communication problems. Shield on communication cable is to remain continuous and ground only at the controller. You need a special Ethernet cable for realizing this communication protocol. There are many categories of Ethernet cables we can use like CAT-4, CAT-5, CAT-5E, CAT-6, CAT-6A, etc. In our tutorial, we are going to use CAT-6E cable which has 4 twisted pairs of 24AWG wires and can support up to 600MHz. It is terminated at both ends by an RJ45 connector. It is not a standard Communication protocol, but it is a physical circuit with which you can transmit and receive serial data with other peripherals. Unlike the standard RS232 protocol, what is rs485 cable RS485 allows many communicating parties to share the same 3-wire communications cable. RS232 allows both communicating parties to transmit and receive data at the same time; this is referred to as full duplex communications. But there are some limitations to it as it cannot support multiple slaves and multiple masters and the maximum data frame is limited to 9 bits.
It works on half-duplex communication to implement the function of converting the TTL level into RS-485 level which means it can either transmit or receive at any time, not both, it can achieve a maximum transmission rate of 2.5Mbps. MAX485 transceiver draws a supply current of between 120μA and 500μA under the unloaded or fully loaded conditions when the driver is disabled. Previously we have also performed MAX485 communication with Arduino and also MAX485 Communication with Raspberry pi, you can also check them out if interested. In this tutorial, we are going to learn about the RS485 communication protocol and how to implement it with the two Arduino Nano we have with us and how to use the MAX485 RS485 to UART conversion Module. UART is an Asynchronous transmission device hence there is no clock signal to sync the data between the two devices instead it uses start and stop bits at the start and end of each data packet respectively to mark the extremities of the data being transferred. Signal High and Lows are measured against the GND level so shifting the GND level will have a disastrous effect on the data transfer. For the transfer of data, the baud rates of both Master and Slave must be between 10% of each other.
There are many different types of serial communication protocols like I2C and SPI which can be easily implemented with Arduino and today we are going to look at another most commonly used protocol called RS485 which is very commonly used in high noise industrial environments to transfer the data over a long distance. 1200 is the baud rate that you choose; you can specify any standard baud rate up to 4800 baud. If A is negative with respect to B, the state is binary 1. The reversed polarity (A positive with respect to B) is binary 0. The standard does not assign any logic function to the two states. The receiver input has a fail-safe feature that guarantees logic high output if the input is open circuit. The truth tables of most popular devices, starting with the SN75176, show the output signals inverted. We will send some data from the transmitter side over the cable from the Nano which is converted to RS485 signals via MAX RS485 Module working in Master Mode.
While handshaking is still with us, it is usually best to disable it in software (if possible) and/or "loop-back" the pairs of signals (RTS to CTS, DTR to DSR, etc.) While RS232 was rumored to be on the "way out" with the advent of many of the new communications standards, it is still alive and well today. It is very well documented and widely used and it also has a parity bit to allow for error checking. Each packet contains 1 start bit, 5 to 9 data bits (depending on the UART), an optional parity bit, and 1 or 2 stop bits. 2 Alphanumeric LCD, and MAX485 UART to RS485 converter IC connected to each end of an Ethernet Cat-6E cable via an RJ45 connector. The QScreen Controller’s transmit data signal TxD1 (pin 2 on the 9-pin serial connector) is connected to the terminal’s receive data signal RxD (pin 2 on its 9-pin connector).